Coatings

Seal-A-Pore® HP

Protects Masonry Surfaces
Protects Interior Wall Surfaces
Improves and Preserves Building Appearance

Seal-A-Pore HP is a high-performance, solvent-based silane sealer that forms an invisible water-repellent surface, allowing the substrate to maintain its original appearance. This transparent, colorless, thin liquid sealer penetrates deeply into tiny pores and protects mortar joints to minimize damage caused by expansion and contraction due to freeze/thaw cycles.

Speak with a Rep

Product Specifications

Method	Description
Spray	Apply Seal-A-Pore HP continuously, ensuring no pinholes or gaps are left on the substrate. Do not allow the material to puddle. Spray apply with a low pressure, solvent resistant, airless or pump sprayer equipped with a fan nozzle orifice of 0.025” to 0.030” at 0.5 gpm. The optimum spray pattern is an 8” to 12” (20.32 cm to 30.48 cm) fan. Hold sprayer tip 8” to 12” (20.32 cm to 30.48 cm) from the surface of the concrete. Begin application at the bottom, working your way up while allowing a 6” to 12” (15.24 cm to 30.48 cm) run down. Excessive run down or over application can cause discoloration of the substrate. Directly after spraying back roll surfaces using a short nap (1/4” max) solvent and shed resistant roller. Allow 6” (15.24 cm) minimum run down. Maximum run down is 12” (30.48 cm). Excessive run down or over application can cause discoloration of the substrate. Material is usually dry after 1 (one) hour at 72°F (22°C) with 50% R.H. When using a brush for application, dab or splash the material on the surface. Seal-A-Pore HP is a thin, low viscosity liquid and does not brush out like paint.
Brush	If spraying, use a coarse round nozzle to ensure a generously wetting out of the surface. Applying the product heavily should have no adverse effect on performance. If desired, an additional coat or touch up coat is acceptable as needed. (If spray applying this product, please see our spray application guide).

Method

Description

Spray

Apply Seal-A-Pore HP continuously, ensuring no pinholes or gaps are left on the substrate. Do not allow the material to puddle. Spray apply with a low pressure, solvent resistant, airless or pump sprayer equipped with a fan nozzle orifice of 0.025” to 0.030” at 0.5 gpm. The optimum spray pattern is an 8” to 12” (20.32 cm to 30.48 cm) fan. Hold sprayer tip 8” to 12” (20.32 cm to 30.48 cm) from the surface of the concrete. Begin application at the bottom, working your way up while allowing a 6” to 12” (15.24 cm to 30.48 cm) run down. Excessive run down or over application can cause discoloration of the substrate. Directly after spraying back roll surfaces using a short nap (1/4” max) solvent and shed resistant roller. Allow 6” (15.24 cm) minimum run down. Maximum run down is 12” (30.48 cm). Excessive run down or over application can cause discoloration of the substrate. Material is usually dry after 1 (one) hour at 72°F (22°C) with 50% R.H. When using a brush for application, dab or splash the material on the surface. Seal-A-Pore HP is a thin, low viscosity liquid and does not brush out like paint.

Brush

If spraying, use a coarse round nozzle to ensure a generously wetting out of the surface. Applying the product heavily should have no adverse effect on performance. If desired, an additional coat or touch up coat is acceptable as needed. (If spray applying this product, please see our spray application guide).

Eco-Fact	Value
VOC	< 250 gal/l

Type	Link
Data Sheets	Seal-A-Pore HP Technical Data Sheet
SDS	Seal-A-Pore HP Safety Data Sheet
Benefits	Seal-A-Pore HP Benefits

Features

Garland Metal Project Photos from IMETCO

Improves and Preserves Building Appearance

Seal-A-Pore HP is a colorless liquid that will not change the appearance of the masonry surface on which it is applied. Seal-A-Pore HP minimizes exterior masonry staining, flaking, and temporary discoloration caused by absorbed moisture. Seal-A-Pore HP will not reduce efflorescence if present due to wall design.

Modified Bitumen

KEE / Thermoplastic

Standing Seam Metal Roofing

Wall Panels & Rainscreens

Edge Metal

Metal Accessories

Restoration Systems

Metal

Modified Bitumen Roof Surface Coatings

Facades / Walls

Traffic Grade

Flooring

Garland's Process

Roof Assessment

Envelope Services

OMNIA Partners

Vizient

Premier Partners

GSA

CMAS (CA)

COMMBUYS (MA)

EducationPlus (MO)

Equalis Group (OH)

Vegetative Roofing

Solar Roofs

K-12

Higher Education

Garland Federal Division

Garland Federal Partner Program

Municipalities

Correctional Facilities

First Responders

Rec Centers & Natatoriums

Architects & Design Professionals

Coatings

Seal-A-Pore® HP

Product Specifications

Technical Data

Application

Sustainability

Documents

Features

Protects Masonry Surfaces

Protects Interior Wall Surfaces

Improves and Preserves Building Appearance

Related Products

Green-Lock® Sealant XL

Tuff-Stuff® MS Sealant

R-Mer® Seal